Hi,
I have a SR1500PAL server with a intel RMM2
When i access the webpage and try to run the console ,
java opens and i can see the hosts screen, however its not not working with keyboard and mouse during a KVM
I have a window 7 home, java 5, when i choose other O/S on kvm settings mouse sync dosnt work(says unable to sync) on the left corner, or the keyboard and with windows/mac setting on.
the Host OS is running 2008 R2
any idea why it dosnt work?
I'm using some Intel AXX6DRV3GR and AXX4DRV3GR backplanes. Before I buy new HDDs I need to know whether power pin 3 of the AXX6DRV3GR's HDD connectors are connected or not connected. And if they are connected, are they connected to 0 V or to 3.3 V?
I'm asking this because some new HDDs will not power up if P3 is not connected to 0 V.
Power Disable Pin (Pin3) is a new feature in the SATA 3.3 industry standard specification (published in February 2016). And on SAS 3.0, P3 is used to redefine as a POWER DISABLE signal.
Have s5000psl board mounted in SC5400 Intel chassis. Chassis has redundant PS plugged into FRIG2PDB.
Shutdown working server, removed power, opened chassis to blow out dust. Server will not power up.
Neither of the plugged in power supplies lights up any indicator LEDs. I suspect FRIIG2PDB to somehow have failed when powering off the unit.
I'd welcome any additional ideas.
Thank you,
Hi,
we've tried to update the MB BIOS to the latest version available at the site (068).
Download Security BIOS update for S5500/S5520 products
The original version we had - 038.
The flashing went without any errors. According to the startup.nsh the first step has been the flashing of the transition capsule (IFlash32.efi T066.cap /u /ni).
After the first reboot server won't start: no video and a continuous beep from the RAID controller board beeper (midplane).
And the BIOS recovery procedure won't boot it either:
And the BIOS recovery procedure won't boot it either. The video won't come up, the flash drive flashes and then the diagnostic LEDs switch to some combination that we were unable to find in the board technical manual.
The video is linked below.
BTW, the CPU is Xeon 5520 .
Any ideas on why the recovery procedure fails?
Is there any ports on the board to reprogram the flash chip without unsoldering?
Thanks in advance!
I fitted a S2600CP with 2*E5-2670 and 128GB Reg ECC in a tower case. The system was running normally for a month. I was using a GT610 and tried to replace it by a GTS450. The system just won't start even if I switched back to GT610. As long as I plug in the power cord, the blue SYSTEM ID LED will blink for several seconds, then turn constantly for around 1 minute and go out finally. The other LEDs are in green like normal. If I push the power button all the fans will rotate for less than 1 second and stop. I didn't find any visible damage on the board so there must be something wrong with the software. Anyone encountered the same problem? How to solve that? Thanks.
it will be very fine, if you give me link for download update fo this device
I've built a small file server around the S1200SPO. This is for a small company that has no riser room, or server room. The file server sits in an open concept office, but the fan noise is higher than their last Dell server so I'm trying to bring it down. I've set the option to "acoustic" mode in the BIOS but the fans continue to spin at full all the time. I thought that they would settle after the boot but they do not. They stay high. I know the chipset drivers are installed and there doesn't seem to be any drivers missing. Any ideas what I can try?
Hello everyone,
The title of this post matches another post on this forum which was never answered and is 6 years old which is why I started a new thread.
I have been using the intel s5520sc motherboard for about 5 years now and I have always used only one CPU (xeon x5680 SLBV5). I purchased an identical second CPU recently but whenever I install it the system refuses to boot.
The system status led is green but the post diagnostic LEDS don't function at all. The fans run at max speed but there is no output. The RAM I use is in the official supported list for this motherboard. When I use only
one CPU (even the new one) everything boots without issues. I've tried booting without ram but then the system status led is orange and besides that there is no difference in booting compared to when RAM is present. Neither of the CPUs are engineering samples.
The power for the second CPU was plugged in. There are no bent pins on socket 2 BUT one pin is missing from socket 1 (but this has been so for years and I've never noticed it - picture included). I also have the latest BIOS for this motherboard (v63).
Any ideas would be greatly appreciated!
Thank you!
Regards,
Usui
I have the c600 rksas8 chip installed to enable the use of both onboard SAS ports on the s2600ip4 motherboard.
What settings is required in bios and in esxi 6 to enable the passsthrough of the SAS drives on these controllers?
thanks
Dear Intel,
I understand the motherboard of S5000VSA is already end of support, btw i would like to double confirm, is there any latest bios because what i have now is S5000.86B.15.00.0101, but when i run the bisoagentplus.com, the report shown the board still have a latest bios and i have to subscribe the software.
Please confirm. TQ
I was just wondering if anybody has any experience with Intel S2600CWTR series serverboards and Xeon 2600 V4 processors.
It boots fine with single CPU E5-2600 V4 and also with dual E5-2600 V3 .... but not with dual V4.
Intel says only board rev H12882-260 has this issue .... but not H12882-261 or H12882-262 ... so they sent me new boards ... update BIOS to latest rev 16 but still the same problem.
I really want to use the V4 because of better memory bandwidth, but I may have to downgrade to V3.
Anybody know anything about this issue?
Many thanks for any insight.
We’re using the E3-1275v5 processor with Kingston 8GB DDR4 DIMMs. The Kingston pn is KVR21E15D8/8. I have checked the jumpers and cables and those look O.K. I took the DIMMs out and then the system responds with 3 long beeps that says I have a memory error. So that part works and it appears the processor is alive. I checked the diagnostic LEDs. If I am reading them correctly, it appears the system stops on 4Fh. Also, the blinking LED next to the 8 diagnostic LEDs goes from blinking green to a solid amber. Then after a short time the machine reboots.
I'm trying to install the latest version of Raid Web Console 2 on my server (I was running the version 14 before) and I got this error 
Hello
There is a problem with the server on S1200V3RP platform.
On the server has two disk to 2 TB in RAID1 (Used Programnyj RAID Intel Rapid Storage Technology). Suddenly, the server became very slow, disk write speed dropped to 1Mb / s. Status RAID rebuild. SMART drives both said that the wheels are in good condition. In spite of this I replaced the disk on which relied RAID and waited for the completion of rebuilding. I decided to work with one disk in a RAID and do backups on a network drive. A day later, the server is turned off independently. RAID is not seen any drive. It was possible to run the system after use after the Configuration Utility and recovery volume ... Tell me what could be the problem?
We recently bought the S2600CW serverboard for our school and we are required to install Ubuntu 11.10 and Squid 2.7 to have the server act as a proxy server. However, our problem is installing the Ubuntu 11.10. We encountered repeating error messages. We are looking for solution or anything that can help us install Ubuntu 11.10. Thanks
Does the s1200v3rpl support cachecade?
I see it listed as an option in the RAID web console but I can't find any supporting documentation.
The s1200v3rpl is part of a P4308RPLSHDR.
Thanks in advance!
Hi,
I have a SR1500PAL server with a intel RMM2
When i access the webpage and try to run the console ,
java opens and i can see the hosts screen, however its not not working with keyboard and mouse during a KVM
I have a window 7 home, java 5, when i choose other O/S on kvm settings mouse sync dosnt work(says unable to sync) on the left corner, or the keyboard and with windows/mac setting on.
the Host OS is running 2008 R2
any idea why it dosnt work?
Have s5000psl board mounted in SC5400 Intel chassis. Chassis has redundant PS plugged into FRIG2PDB.
Shutdown working server, removed power, opened chassis to blow out dust. Server will not power up.
Neither of the plugged in power supplies lights up any indicator LEDs. I suspect FRIIG2PDB to somehow have failed when powering off the unit.
I'd welcome any additional ideas.
Thank you,
Hello,
I've a SS4000-e with 2 hard-disks and configured as RAID 1. Now the SS4000-E have a problem. I cannot connect via the networkdrive with Windows, MAC OS and Unix.
I can login to the adminpannel over webbrowser and all looks good, but I cannot save any changes (error in browser).
So I've put the harddisk out and put it in my PC. How can I read the partition to save the data?
Thanks
Stefan