Hi,
I have a SR1500PAL server with a intel RMM2
When i access the webpage and try to run the console ,
java opens and i can see the hosts screen, however its not not working with keyboard and mouse during a KVM
I have a window 7 home, java 5, when i choose other O/S on kvm settings mouse sync dosnt work(says unable to sync) on the left corner, or the keyboard and with windows/mac setting on.
the Host OS is running 2008 R2
any idea why it dosnt work?
Or what is the "maximum" CPU for this board?
I have a machine that has integrated Intel HD 2500 graphics on it. I am able to find drivers for client OS's like Windows 7, 8, 8.1, 10, etc but nothing for Servers. They do detect the hardware appropriately and install but upon a reboot after installation the Windows logo starts and then everything goes black. Uninstalling the driver via Safe Mode brings Windows back up but using the Generic Graphics driver from Windows. Has anyone successfully been able to get HD 2500's to work under a server os?
I want to do a clean install of 64-bit Windows 7 Pro on the R1304WTTGSR server (S2600W motherboard). The specs for this server say Windows 7 EFI is compatible and has been tested with this server.
The specific configuration is
2 x Xeon processor E5 2630 v4
2 x 64 GB ECC LRDIMM DDR4 memory
2 x Seagate 8 TB hard drives
Panasonic BD Blu-ray drive
Radeon XFX R5 230 graphics card, installed in riser slot 1.
Mouse and keyboard connected via front USB port (using a splitter).
LAN-see below
The firmware ("BIOS") is set to boot using EFI. AFAIK, this means it cannot boot using BIOS ("Legacy") mode.
When I boot the Windows installation disk (latest version of Windows 7 x64 from Microsoft web site), using EFI, the screen shows first "Loading files", then "Starting WIndows". At this point:
- With nothing connected to the network ports (LAN), the system hangs. By "hangs" I mean nothing changing on the screen, no DVD or disk activity, no response to mouse or keyboard, and no response when front panel power button is pushed.
- With a CAT5 (Ethernet) cable connected between network ports 1 and 2, the system proceeds with some animation of the Windows flag (fading and brightening), but other than this, the system hangs as above. The reason for connecting the network ports is that someone posted that there is a bug in the Windows 7 install disk network drivers, that they hang when nothing is connected.
In either case, waits of several hours does not matter--the system is frozen.
I also thought of installing from USB drive, but without success. The Microsoft Windows7-USB-DVD-Download-Tool-Installer does not produce an EFI-bootable result, nor does Rufus 2.10.973 (the current version). I created a Windows 10 USB drive using a different Microsoft tool, MediaCreationTool, and it is EFI-bootable, but requires that I load the disk drivers.
Although it may be unrelated, the last thing I tried was resetting the BIOS to factory defaults (F9). That made my add-in video card stop working, even though it was enabled in the BIOS.
BIOS version is SE5C610.86B.01.01.0016 (3/31/2016). The server did not come with any software.
If anyone has successfully done this installation, please share the secret steps needed to do so.
Hi,
we've tried to update the MB BIOS to the latest version available at the site (068).
Download Security BIOS update for S5500/S5520 products
The original version we had - 038.
The flashing went without any errors. According to the startup.nsh the first step has been the flashing of the transition capsule (IFlash32.efi T066.cap /u /ni).
After the first reboot server won't start: no video and a continuous beep from the RAID controller board beeper (midplane).
And the BIOS recovery procedure won't boot it either:
And the BIOS recovery procedure won't boot it either. The video won't come up, the flash drive flashes and then the diagnostic LEDs switch to some combination that we were unable to find in the board technical manual.
The video is linked below.
BTW, the CPU is Xeon 5520 .
Any ideas on why the recovery procedure fails?
Is there any ports on the board to reprogram the flash chip without unsoldering?
Thanks in advance!
Intel Server Board S1200SPL.
В режиме Intel RSTe 4 RAID1 есть ли режим обновления тома "По запросу", как в более ранних Intel Server Board?
Этот режим необходим для защиты от воздействия вирусов.
Есть ли такой режим (RAID1 с ручным обновлением "По запросу") в режиме Intel ESRT2?
В описании ESRT2_Software_UG.pdf об этом ничего не сказано:
http://www.intel.com/content/www/us/en/support/boards-and-kits/000005760.html
http://www.intel.ru/content/www/ru/ru/support/boards-and-kits/000005760.html
Intel Server Board S1200SPL имеет том RAID1 (с ручным обновлением "По запросу")
в режиме Intel RSTe 4 (Intel Rapid Storage Technology (RST)).
Поддерживается ли в этом режиме технология Intel® Smart Response Technology?
Можно ли использовать в качестве дисков для ускорения:
1. M.2 SATA SSD (2242 form factor)
или
2. SATA DOM (Disk on Module) на порту SATA4?
I have a number of S2600CWTR boards .... these boards have two 7-pin SATA ports. What do you recommend for people that need more ... is there an add-on SATA controller that you recommend?
Hallo,
i try to install my own Secure Boot PK Cert but dont can find an way to remove the
pre installed. So Secure Boot runs in User Mode and i cant get in Setup Mode.
Is there a way to remove the PK key oder get Secure Boot into Setup Mode?
What i found is that some Intel Boards have the Bios Menu entry to set Secure Boot Mode to Custome but this dont.
With Keytools i dont can remove the installed PK without an auth file that i dont have.
And can i even prove that this PK is really from Intel?
Used last Updates:
BIOS ID : SE5C610.86B.01.01.0016.033120161139
BMC FW Rev : 1.43.9685
Boot FW Rev : 1.07
SDR Package Version : SDR Package 1.13
Mgmt Engine (ME) FW Rev : 03.01.03.021
Product Name : S2600CWR
Part/Model Number : H12882-260
On Board Installed: TPM AXXTPME5 (but not active)
Bios Options
Keytool
Hello!
I recently bought an used s5520hc mainboard. I tried to boot it with a 600w psu that is actually for desktopcomputers. It has only one 4-pin connector for the first cpu instead of two eight-pin connector for both cpu's. I just wanted to check if the board could boot. After a few seconds there was this beep signal: 1-5-4-4 ("Power good assertion timeout - Power unit sensors report soft power control failure offset."). Now my question is whether it is more likely that the board is bad (I read about some issues in some forums []Intel S5520HC and SR5650BRP]) or the problem can be solved by buying a sc5600 chassis with powersupplies (750w).
Hello! Can i install GTX 980Ti in chassis P4304XXMUXX ?! MB S2600CW2R, Card length 30.5 cm. Thanks.
I have a new to me H2312XXKR chassis with four HNS2600WP blades. I added RAM and CPU to one blade and tried to boot it but get no VGA signal. The same RAM DDR3 1600 and CPUs E5-2650 V2 work in another 2600WP blade just fine. This one seems to be new and never used. Is there a trick to setting up these boards for the first time?
Hello,
We installed a new server with motherboard s2600cw. The Server freezes completely and a force restart is required when virtual machines are running on SSD drivers. This doesn't happen on mechanical hard disks. We suspect some issue between the controller and the Gen2 SCSI virtual machines running on Hyper-V. Please assist.
Regards,
CompNet
Hi,
Our customer faces a problem with servers in a cluster rebooting upon logging PCIe ACS Violation error.
71 08/03/2016 12:48:55 BIOS Evt Sensor System Event reports OEM System Boot Event - Asserted
70 08/03/2016 12:48:04 PCIe Fatal Error Critical Interrupt ACS Violation on bus: 0, device: 1, function: 0. - Asserted
They tried to update the IB card FW to the newest version (10.12.0780) but without success.
Could you please check the issue and let us know about the possible actions/problem source?
For more information please see the attached service data.
Hi all,
I just changed a new MB for intel server. This MB has model S2600WT.. After assemble all parts in this server and plug the power cable, System self check for a few second, everything seem be ok. When I press power switch on, all fans running up at high speed and not slow down as normal, The front LCD of system show orange color with error " Watchdog asserted" and system is not show video too.
Please kindly help me to explain what is root problem and how to fix it.
Thanks and best regards
Trinh Nguyen
Hi everyone.
I want to build to build a squid proxy and samba server with minimal cost. Does Intel S1200SPS support non-Ecc memory and Pentium G4400 or Core i3-6100 processor.
Thank you.
Hello people,
I have connected the 4 pin power connector into the bay backplane PCB, I have connected the mini-SAS to x4 SATA cable 1 per black sata port on the motherboard (as its advised not to use the 2 white SATA ports). I have also connected the IC2 cable, the sata ports are in AHCI mode. When I power on the server I can see the amber light on the drive cages flash for 0.1 seconds or so but after that its dead, drives do not spin and are not seen in the BIOS.
I have recently run an BIOS upgrade process that upgraded various parts of the motherboard and it did detect the 8x2.5" hotswap bay within that so I believe its working as it should be.... yet its not seen within the BIOS or windows. Am I missing a BIOS setting somewhere or something?
Intel S2600CP2J motherboard
Intel 8x 2.5inch hot swap bay (A2U8X25S3HSDK) comes with the IC2 + mini-sata to 4x SATA cable.
Intel P4208XXMHGC server chassis
Any pointers will be much appreciated,
thanks!
подскажите по совместимости оборудования: материнская плата S5520HC и контроллер RS2BL080. надо - расширить дисковое пространство. Совместимо ли с этим: дисковая полка JBOD2312S3SP и RAID Expander RES3FV288? или есть другой вариант оборудования?
Hi.
There are two partworked servers:
1. sr2600urlxr with no boot. Bad cooling is the reason. No beeps and 8led indication. system led is amber. With another type of PSU - 1544 and 1542 beeps with random of two volumes of sounds. Probably MB is failed.
2. sr2600urbrp with no boot. 1544 and 1542 beeps. Probably PSUs are failed.
Need to assemble server with SAS.
With server 2. midplane, PSUs, processors replaced from 1., new RAM installed.
It's started, but no midplane BIOS screen appears (like "press CTRL+G for enter setup"). In main BIOS no entries for SAS - only onboard SATA. And no any info about DVD in backplane.
Firmware upgrades looks good. Versions in BIOS are changed.
Googling show me intersting file in FRU firmware upgrade - MASTER.CFG. I modified it - remove set for sr2600urbrp and force "CHASSIS_MENU" for select URLX as target system.
It's looks good, no errors messages while upgrade, but after reset no SAS yet and new upgrade with original MASTER.CFG shows URBRP again.
Is there right way to add falsasmp2 to sr2600urbrp system?
Also i'm not sure that falsasmp2 is not failed and i have no system to test it. But frontpanel buttons are worked, fans - rotated, cooler above SAS chip is warmed.
And sorry for my english.
UPD. There is RMM3 module onboard. FRU firmware detect urlx but no sas:
It has four ram slots..
Can I add 8gb ram in a single slot or else do I have to split it into 4 * 2